Megan
I wanted to add a bit of information to Jim Glenn’s recommendation. Austin’s Art In Public Places program (AIPP) uses a similar method. When fabricated we ask the manufacturer to create 4 threaded holes in the back of the plaque. These holes are an inch from each corner and only need to be 4 threads deep. Imagine screwing a bolt into a nut and spinning it 4 times. This is important because the thickness of the plaque requires a minimum depth of those 4 rotations.
I ask that the manufacture provide us with the appropriate sized threaded rod to fit each of the holes. Typically, I ask that they be 2 inches in length. They can be cut down if needed.
After I drill holes into the concrete to match my hole pattern on the plaque (for this I use a piece of paper) I spread a 2 part epoxy on the back of the plaque and onto the 2 inch threaded rods. You contractor must make sure they are level and firmly pressed against the concrete while this cures. Avoid any gaps that would allow someone to insert a small tool between the plaque and concrete. Lastly, make sure your installer does the epoxy work on a warm, dry day after a couple days without rain. You’ll need a dry surfaces for the adhesive to saturate the concrete. It can rain cats and dogs a few hours after the adhesive is set but not before. I hope this helps!
-Frank Wick
Frank Wick
Collection Manager
Art In Public Places Program / Cultural Arts Division
City of Austin Economic Development Department
201 East 2nd Street, Suite A
512.974.2576
austincreates.com / facebook.com/CityofAustinArts
From: public_art_network@
americansforthearts. [mailto:public_art_network@simplelists.com americansforthearts. ] On Behalf Of Jim Glennsimplelists.com
Sent: Tuesday, April 10, 2018 12:13 PM
To: public_art_network@americansforthearts. simplelists.com
Subject: Re: signage on outdoor public art
Hi Megan:
Our outdoor plaques have a threaded bolts (2) that screw into the back of the plaque and then are expoxied into a hole we drill into the concrete or wall. It is not guaranteed theft proof but with that and any additional adhesive on the back of the plaque will make it a little more difficult.
Good luck.
Jim
Jim Glenn
Utah Division of Arts & Museums
Manager - Collections, Design, Visual and Public Art
Office 801-245 7271 - Mobile 801-808-4557
On Tue, Apr 10, 2018 at 11:07 AM, Megan Berner <bernerm@reno.gov> wrote:
Hi all,
We are working on getting all of our outdoor public art labeled. Currently, we have a few different types of signage--most of it is metal (stainless steel or otherwise) that is bolted to concrete or the base of the sculpture. However, we have an issue with signage getting stolen.
I'm wondering if any of you have experience with this and have found something that works well and is not enticing to steal or vandalize. Engraved stainless is pretty expensive when you are looking at labeling 75 pieces of art. What is the best way to attach the signage so that it can't be stolen? Any information would be appreciated. Thank you!
Megan
Megan Berner
Public Art Program Coordinator
Office of the City Manager
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it may contain confidential information that is also legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this transmission is prohibited. If you have received this transmission in error, please immediately notify the sender and immediately destroy the original transmission and its attachments without reading or saving in any manner. Thank you.
To unsubscribe from this list please go to http://archives.simplelists.
com
To unsubscribe from this list please go to http://archives.simplelists.
com To unsubscribe from this list please go to http://www.simplelists.com/
confirm.php?u= lFlLKgRlpdzqeHpKW5SWSEcH3KmMuZ XZ
